- 您现在的位置：买卖IC网 > Sheet目录19106 > CUB5B000 (Red Lion Controls)COUNTER/RATE IND DUAL RD/GN BKLT
6.1 MODULE 1 - I NPUT S ETUP P ARAMETERS ( 1-INPUt )
1-INPUt
SEL
INP A-b
CntA dP
CntA ScF
CntA rSt
CntA dir
PARAMETER MENU
Dual Count or Batch
Only
CntA Ld Cntb bAt Cntb dP Cntb ScF
RSt P-UP
USEr INP
Dual Count
or Batch
Only
USEr ASN
Pro
Count
Mode
Counter A
Decimal Point
Counter A
Scale Factor
Counter A
Reset Action
Counter A
Count
Direction
Counter A
Count Load
Value
Counter B
Batch Count
Enable
Counter B
Decimal Point
Counter B
Scale Factor
Counter Reset
at Power-up
User Input
Function
User Input
Assignment
Shaded area selections only apply when Counter B is enabled (Dual Counter
mode or batch counter).
COUNT MODE
COUNTER A COUNT LOAD VALUE
? 00000500
INP A-b ?
? Cnt ud
Cnt ud
RAtE Cnt
dUAL Cnt
qUAd 1
qUAd 2
qUAd 4
Add Add
Add Sub
CmtA Ld ?
-9999999 to 99999999
Counter A resets to this value if Reset to Count Load action is selected.
?
NO
Select the count mode that corresponds with your application. The input
actions are shown in the boxes below. For simple counting applications, it is
recommended to use Count with Direction for the count mode. Simply leave the
direction input unconnected.
DISPLAY MODE INPUT A ACTION INPUT B ACTION
Cnt ud Count with Direction Counter A Counter A Direction
RAtE Cnt Rate/Counter Rate only Counter A Add
dUAL Cnt Dual Counter Counter A Add Counter B Add
COUNTER B BATCH COUNT ENABLE
Cmtb bAt ? NO SP2
SP1 SP1-2
The Counter B batch count function internally counts the number of output
activations of the selected setpoint(s). The count source for the batch counter
can be SP1, SP2 or both. Batch counting is available in all count modes except
Dual Counter, which uses an external input signal for Counter B. This
parameter only appears if a Setpoint Output option card is installed.
qUAd 1 Quadrature x1
Count A
Quad A
qUAd 2 Quadrature x2
Count A
Quad A
COUNTER B DECIMAL POSITION
? 0
? 0
?
01.0000
RSt P-UP ?
qUAd 4 Quadrature x4 CountA QuadA
Add Add 2 Input Add/Add Counter A Add Counter A Add
Add Sub 2 Input Add/Subtract Counter A Add Counter A Subtract
Note: The Rate indicator signal is derived from Input A in all count modes.
COUNTER A DECIMAL POSITION
CntA dP ? 0 0.00 0.0000
0.0 0.000 0.00000
This selects the decimal point position for Counter A. The selection will also
affect Counter A scale factor calculations.
COUNTER A SCALE FACTOR
CmtA ScF ?
00.0001 to 99.9999
The number of input counts is multiplied by the scale factor to obtain the
desired process value. A scale factor of 1.0000 will result in the display of the
actual number of input counts. (Details on scaling calculations are explained at
the end of this section.)*
COUNTER A RESET ACTION
CmtA rSt ? to 2Ero to CtLd
? to 2Ero
When Counter A is reset, it returns to Zero or Counter A Count Load value.
This reset action applies to all Counter A resets, except a setpoint generated
Counter Auto Reset programmed in Module 4.
COUNTER A COUNT DIRECTION
Cntb dP ? 0 0.00 0.0000
0.0 0.000 0.00000
This selects the decimal point position for Counter B. The selection will also
affect Counter B scale factor calculations.
COUNTER B SCALE FACTOR
Cntb ScF ? 00.0001 to 99.9999
? 01.0000
The number of input or batch counts is multiplied by the scale factor to
obtain the desired process value. A scale factor of 1.0000 will result in the
display of the actual number of input or batch counts. (Details on scaling
calculations are explained at the end of this section.)*
COUNTER RESET AT POWER-UP
NO NO Count b
? NO yES Count A both A-b
The selected counter(s) will reset at each meter power-up.
* For value entry instructions, refer to selection/value entry in the Programming
The Meter section.
CmtA dir
?
?
NOr
NOr
rEV
Reverse ( rEV ) switches the normal Counter A count direction shown in the
Count Mode parameter chart.
7
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
P51-50-A-J-P-5V-000-000
SENSOR 50PSI 3/8-24 UNF 1-5V
P51-15-A-J-P-5V-000-000
SENSOR 15PSI 3/8-24 UNF 1-5V
CUB5R000
COUNTER/RATE IND DUAL REFL DISPL
P51-750-A-I-P-5V-000-000
SENSOR 750PSI 7/16-20 UNF 1-5V
ASFLMPC-48.000MHZ-Z-T
OSC 48.000 MHZ CMOS MEMS SMD
P51-500-A-I-P-5V-000-000
SENSOR 500PSI 7/16-20 UNF 1-5V
P51-300-A-I-P-5V-000-000
SENSOR 300PSI 7/16-20 UNF 1-5V
P51-200-A-I-P-5V-000-000
SENSOR 200PSI 7/16-20 UNF 1-5V
相关代理商/技术参数
CUB5B000 CAL D
制造商:Red Lion Controls 功能描述:CALIBRATED W/DATA - Multifunction Counter, No. of Digits / Alpha:8, Digit Height
CUB5COM1
功能描述:RS485 SERIAL COMMO CARD RoHS:是 类别:工业控制，仪表 >> 仪表 - 面板，数字 系列:* 标准包装:12 系列:* 其它名称:Q7072030
CUB5COM2
功能描述:RS232 SERIAL COMM CARD FOR CUB5 RoHS:是 类别:工业控制，仪表 >> 配件 系列:* 标准包装:1 系列:Aero-Motive® 130117 附件类型:拖车带 适用于相关产品:标准盒式跟踪系统 其它名称:WM6183
CUB5IB00
功能描述:DC METER RED/GREEN BKLT RoHS:是 类别:工业控制，仪表 >> 仪表 - 面板，数字 系列:* 标准包装:12 系列:* 其它名称:Q7072030
CUB5IB00 CALIBRATED
制造商:Red Lion Controls 功能描述:DIGITAL PANEL METER MODEL CUB5 WITH CERTIFICATE OF CALIBRATION
CUB5IR00
功能描述:DC METER REFLECTIVE DISP RoHS:是 类别:工业控制，仪表 >> 仪表 - 面板，数字 系列:* 标准包装:12 系列:* 其它名称:Q7072030
CUB5OEMS
制造商:Red Lion Controls 功能描述:PROGRAMMING KIT FOR SOFTWARE
CUB5PB00
功能描述:PROCESS METER RED/GREEN BKLT RoHS:是 类别:工业控制，仪表 >> 仪表 - 面板，数字 系列:* 标准包装:12 系列:* 其它名称:Q7072030